Transparency
The standards behind the work, out in the open.
Good geotechnical work is not a secret. Every borehole logged, every sample tested, and every foundation recommendation follows published codes and standards written by national bodies, not house rules invented to sound impressive.
Below is the actual reference shelf behind these reports, with a link to each source so you can read it yourself. Some are free to view: the building codes are published free by the National Research Council, and Alberta safety rules and the locate service are free government resources. Others are sold by the organizations that maintain them, so those links go to the official store rather than a free copy.
If a standard governs a decision in your report, it will be named. That is the whole point. Withholding the standards has never made a report more sound.

Building and foundation codes (Alberta)
The codes in force for building and foundation work in Alberta. Published free by the National Research Council and adopted by the Province.
The building code in force in Alberta: foundations, excavation, and structural requirements. Foundations sit under Division B, Part 4 (larger buildings) and Part 9 (housing).
The national model code the Alberta Edition builds on.
Read or download all national model codes, free, from the National Research Council.
How the codes are adopted and enforced in Alberta.
Foundation engineering manual
The primary Canadian reference for geotechnical design.
Canadian Geotechnical Society. Bearing capacity, settlement, deep foundations, retaining structures, and slopes. The 4th Ed. (2006) is still widely cited.
Soil classification and laboratory testing (ASTM)
The test methods behind the numbers in a report. ASTM funds its standards work through sales, so these link to the official store rather than a free copy.
The Unified Soil Classification System used to name and group soils.
Describing and identifying soils in the field by sight and feel.
Grain-size distribution of the coarse fraction.
Grain-size distribution of the fine fraction (silt and clay).
Plasticity of fine-grained soils.
Moisture content of soil and rock by mass.
Moisture-density relationship for compaction control.
Higher-energy moisture-density relationship for heavier loading.
Undrained strength of cohesive soils.
Shear-strength parameters for stability and bearing analysis.
Settlement and consolidation behaviour of fine-grained soils.
A basic index property used across other calculations.
Field investigation and drilling (ASTM)
How subsurface conditions are measured and logged in the field.
Split-barrel sampling and N-values, the workhorse of routine drilling.
Continuous electronic profiling of soil behaviour and pore pressure.
Relatively undisturbed sampling of fine-grained soils. Withdrawn in 2024 with no replacement; still standard field practice.
Standard record of what is found in soil and rock down each hole.
Concrete for foundations (CSA)
The Canadian Standards Association codes governing foundation concrete.
Materials and construction of concrete, and the test methods behind it: footings, piles, and foundation walls.
Reinforced-concrete design, including foundations.
Slope stability, retaining and excavation
There is no single Canadian slope code; practice relies on the CFEM, the building code, and these provincial resources.
Government of Alberta guidance on scope and standards for geotechnical investigation.
Legal requirements for excavation, shoring, and worker safety around open ground.
Safety and utility locates before drilling
Nothing goes in the ground until the ground is cleared.
The Alberta locate service (formerly Alberta One-Call). A locate request is placed before every investigation.
Ground disturbance, locate-and-mark, and excavation safety in full.
Professional obligations (APEGA)
The rules a Professional Engineer works under, published free by the regulator.
The full hub of practice standards for engineering work in Alberta.
The stamping and sealing rules that apply to every sealed report.
The ethical duties every APEGA member is held to.
How field reviews are to be carried out and documented.
A note on editions
Standards are revised, withdrawn and replaced over time. Where a standard has recently changed, that is noted above. ASTM D1587 was withdrawn in 2024 but remains standard field practice, and the older grain size method D422 has been replaced by D6913 and D7928. Reports cite the edition actually applied to the work.
Need the ground looked at before you build?
Describe what you are building and where. You get a reply, usually within one business day, setting out what the investigation would cover.
Sealed by Andrew Richardson, P.Eng. Serving southern and central Alberta
